A list of the contents of this article:

How to deal with the newly bought iron pot before use

Cooking oil method: the new pot can be washed with hot water, heated, and then poured into the cooking oil in the pot wall evenly smeared again, placed for 2 hours, so that the treatment can avoid rust. Lard method: first put about 100 grams of lard into a new unwashed pot. After the lard melts, keep shaking the pot body to soak the lard evenly and operate repeatedly for 10 minutes.

You can clean with fat meat: first put the iron pot on the stove to make sure that every place is evenly preheated, and then prepare a piece of fat meat with a fork to fork the meat skin, constantly apply it to all parts of the pot wall with fat meat, and apply it repeatedly to make sure it covers every area until the fat meat turns black.

Method 4: before the use of the new pot, you can pour the right amount of vinegar into the hot iron pot, wash it with a hard brush while burning, pour out the dirty vinegar and wash it with clean water to remove the smell of the new pot. Method 5: buy some fat pork, cut the pork into small pieces, heat the iron pot, and then put the fat into the pot. Keep the heat low and keep smearing the fat in the pan until the fat is fried.

The newly bought iron pot needs to be scrubbed with clean water before it is officially used, which can remove the remaining impurities during smelting, avoid accidental eating and cause discomfort. Put the right amount of water in the pot, start heating, boil for more than ten minutes and then turn off the fire, so that the smell can be removed and the steam will take away the smell and impurities.

Sandpaper grinds off rust. In order to ensure that the iron pot will not rust in the course of daily use, wear off the rust with sandpaper, wash it twice with clean water, fire it on the stove and burn it dry, which can prevent rust. Soak in rice panning water. Pour the rice water into the pan, soak it for a few hours, and then wash it with clean water, which makes it less likely to rust when cooking in the wok.

How to deal with the new pot you just bought before you can use it?

When you just buy a new iron pot, it is recommended to use sandpaper to grind the inner wall of the iron pot, polish all the rust off, pour clean water into the pot, wash it with a brush several times, and then put the iron pot on the gas stove to dry, so you can use the iron pot normally.

If it is a non-stick pan, you can heat it red, pour it into boiling water and bring it to a boil, about 10 minutes after drying. Newly bought iron pot, there is a lot of rust can not be used, you can use sandpaper to wear off the rust, wash it twice with clean water, burn it dry on fire, and then clean it with hot water.

Sandpaper grinds off rust. When the iron pot is just bought, be sure to wear off the rust with sandpaper, then wash both sides with clean water and burn it dry on the gas stove, then it can be used. Soak in rice panning water. Soak the rice in the pan for a few hours, then wash it with clean water so that the rust on it can be easily removed.

The treatment methods of the newly bought iron pot before use include boiling water to dry for 10 minutes, sandpaper to wear off rust, soaking in rice water, and so on.

Boil water and dry for 10 minutes. The new pot just bought is done through classification when dealing with it. Non-stick pots can be boiled and dried in this way for 10 minutes, and other pots have to be treated in different ways. Sandpaper grinds off rust. This way is to prevent the occurrence of rust.

The second day. The new pot needs to be treated before it can be used after it is bought back. In order to prevent the iron pot from rusting, many merchants will apply a layer of antirust oil when the iron pot leaves the factory. This oil is harmful to people, and the oil must be cleaned up before using the iron pot. First of all, we will buy the iron pot with hot water and detergent for the first time, cleaning with detergent is to better remove the impurities in the pot.

How to deal with the newly bought iron pot before use

1, iron pot cooking oil method: the new pot can be washed with hot water, heated, and then poured into the cooking oil in the pot wall evenly smeared again, placed for 2 hours, so that the treatment can avoid rust. Lard method: first put about 100 grams of lard into a new unwashed pot. After the lard melts, keep shaking the pot body to soak the lard evenly and operate repeatedly for 10 minutes.

2. Brushing the iron pot the newly bought pot should be washed clean, first pick up a pot of water, then boil, disinfect the new pot, then pour out the water, scrub the inside of the new pot with a brush, brush off the rust and dust in the new pot, and then dry it.

3. How to open the new iron pot without rust and stickiness? the purpose of the new iron pot is to keep the iron pot from rusting and non-stick in the course of use. here are the steps to open the pot: prepare tools: new iron pot, dishcloth, detergent, cooking oil. Clean the iron pot: first clean the dust and impurities on the surface of the new iron pot with a dishcloth. Smear detergent: apply the detergent evenly on the inner wall of the iron pot, pay attention to smear evenly to avoid residue.

4. The new iron pot needs to be boiled before use, which can prolong the service life of the iron pot. The way to open the pot is to remove all stickers on the body of the pot and wash it with hot water to dry the water behind the pot. Then dry the pot over low heat, prepare a piece of fat meat in the pot, wipe it with a shovel in the pot, make the fat secrete oil in case of heat, wipe every part of the pan evenly; wipe off the lard after 10-15 minutes and wipe the pot clean with a kitchen paper towel.

How to use iron pot for the first time

1. If it is a non-stick pan, you can heat it red, then pour it into boiling water and bring it to a boil. It can be used after about 10 minutes of boiling. Newly bought iron pot, there is a lot of rust can not be used, you can use sandpaper to wear off the rust, wash it twice with clean water, burn it dry on fire, and then clean it with hot water.

2, iron pot cooking oil method: the new pot can be washed with hot water, heated, and then poured into the cooking oil in the pot wall evenly smeared again, placed for 2 hours, so that the treatment can avoid rust. Lard method: first put about 100 grams of lard into a new unwashed pot. After the lard melts, keep shaking the pot body to soak the lard evenly and operate repeatedly for 10 minutes.

3. The treatment methods of the newly bought iron pot before use include boiling water to dry for 10 minutes, sandpaper to wear off rust, soaking in rice water, and so on.

4. The new iron pot will dye the food black when it is cooked for the first time. At this time, you can wipe the food in the pot with bean curd residue several times to prevent the food from being contaminated. When using the new iron pot for the first time, add a spoonful of salt to the iron pot, stir-fry the salt, wipe the pot with salt, and then wipe it clean with a clean cloth. Finally, put some water and oil in the pot and bring it to the boil, the pot will be easy to use.

5. Be careful not to pour out the hot water easily, otherwise the pot will return to drench and the probability of bottom deformation will increase. In short, although it is not necessary to wait 24 hours after boiling the pot, in order to ensure food safety and hygiene and protect health, it is recommended to carry out appropriate cleaning and disinfection before using the new pot, especially when using it for the first time, to ensure that the pot does not contain any residue.

How to use the newly bought iron pot for the first time

Method 1: bring boiling water to a boil. The new iron pot you just bought can burn red on the gas stove; next, pour the boiling water into the hot iron pot and bring it to a boil; it takes about 10 minutes to boil, and then pour out the water. Method 2: sandpaper friction. The new pot you just bought can grind off the rust with sandpaper, then wash it twice with clean water, and finally put it on the gas stove to dry.

Using tea to open a pot the newly bought iron pot can be boiled with tea for the first time. Practice: first put the water and oil into the pot according to the proportion of 1:1, add the tea leaves to the boil, turn the heat down, and wash the pot wall with a spatula or other scoop of oil and tea water. after the oil and water is scalded, you can add fine sand and finally rinse the pot wall with a brush. Open the pot with salt the newly bought iron pot can be boiled with salt for the first time.

For the first time, the new pot boils and dries the newly bought wok with boiling water for 10 minutes. if it is a non-stick pan, it is necessary to heat the pot on the gas stove, then pour the boiling water into it and bring it to a boil. but try to keep the boiling time within 10 minutes.

If it is a non-stick pan, you can heat it red, pour it into boiling water and bring it to a boil, about 10 minutes after drying. Newly bought iron pot, there is a lot of rust can not be used, you can use sandpaper to wear off the rust, wash it twice with clean water, burn it dry on fire, and then clean it with hot water.

Sandpaper: first grind off the rust in the pot with sandpaper, wash it twice with clean water, burn it dry on fire, and finally brush it off with hot water. Cooking oil: heat the pot, spread the cooking oil evenly, and then wash it for a day, which can remove the smell of the iron pot and ensure that the iron pot does not rust. Aged vinegar: heat the new pot, pour in the right amount of aged vinegar, wash it with a hard brush and rinse with clean water to remove the smell of the new pot.